Saturday, September 27, 2014

Front mudguard mounting

Popular opinion (my wife & David) say the front mudguard should be mounted low and not high as I originally intended. Also the CB750 lower triple clamp has no holes for mounting of the guard up high! Just need to figure our a way to mount it to the fork legs. Maybe using some 520 chain and brackets!

Front brake is functional.........at last


I am very pleased to say the we have a fully functioning front brake! The RM250Z front brake cable that I bought originally just had to have it's outer cable shortened by about 100mm. This is possible to do, by carefully grinding down one side of the outer with a grinder till the inner cable is exposed and the carefully (read incredibly laboriously) remove the small sections of outer cable. This is because the inner cable is the right length, and I do not want to remove the crimped end! Anyway I am very happy with the results, the handlebar lever feels really nice and firm. The cable mounts to the same place as the XL500 and is routed through the lower triple clamp like the CB750. I fashioned a pin from an old 12mm axle to attach the end of the cable to the actuator - see pic below.

Tuesday, September 23, 2014

Rewire continued.......


Definitely my least favorite job (but an important one) is the rewiring. I wasn't happy where the harness was just behind the tank as it is very close to the throttle cables! So after a bit of google image searching I found an image showing the harness going from left to right just behind the tank. Top pic also shows the new horn mounted up.

Tuesday, September 16, 2014

How to make your custom project cafe racer bobber motorcycle a success


Think of a dollar amount and double it             
 It's very important to start with the best possible bike you can afford. I think that ideally the bike needs to be in running condition and mostly complete. I have made the mistake of buying a motorcycle (about 1 and a half motorcycles actually) in pieces only to find that the motor was toast and not worth repairing. I paid $368 for this Suzuki 400 (see pic below) on eBay which was in pieces and with many spares, most of which were worn out or junk, luckily I sold it off in parts and made my money back, and most of  the custom parts could be used on my next project. My current project a Honda 500 runs well and is 90% complete, so I could test ride it, only cost me $750. A motorcycle like any other vehicle is worth more in parts than as a whole. Do a quick search on spare parts prices and you will see this. Even a free motorcycle can cost more to finish than that bike you paid $1000 for. A free motorcycle is such probably because it is junk.

Find a bike that is partially realised
See if you can find a project bike that someone has started that fits your design scheme. There are  many reasons why people sell off unfinished projects. People lose interest, realise they are out of their depth, have a change in circumstances like they need cash or move to a place where there is no area to work . Just take a read on your local online classifieds and you will see all the reasons covered.
Don't get in over your head
 Make sure you choose a project that you can complete with your level of skill. If you have to pay someone or a shop to do most of the work - then it's going to be very costly. A visit to your local custom motorcycle store with a how much will this cost question will give you an idea? Spend hours and hours trawling eBay and forums for ideas and methods to achieve your end result. My vintage supermoto Honda XL500S has only one custom made part on it, but it was not by accident, I did loads and loads of research and spent hours trawling online forums etc for information.
Pick the right style of bike as a starting point
Pick the appropriate motorcycle for your project. Cafe racers are a very popular project idea at the moment and seem like an easy conversion, but a sports bike with a perimeter frame will never look like a cafe racer. I saw on a forum recently that someone had bought a Kawasaki ZZR250 for the conversion to a cafe racer, but even with the right tank etc it just doesn't look right due to its frame being the wrong shape.
Modifying your motorcycle and the law
Which brings me to my next point. Modifying motorcycles can lead to major hassles come inspection time, when trying to get a motorcycle re-registered or if you are stopped by the local constabulary questioning if your mods are street legal. Simple things like lengths of mudguards can be easily fixed, but illegal frame modifications cannot. For example as a rule of thumb, you can modify the frame from behind the rear shock mounts without an engineer's certificate, but any mods forward of that will require one (and they are very expensive to obtain - read many thousands of dollars).
Due dilligence
 When you have found a suitable motorcycle, do your due diligence. Check the frame and engine numbers to be certain it is not stolen, has no finance outstanding on it and is not a write-off. Usually this can be done online or over the phone with your local licensing authority. If you are buying a registered bike, then still check that the frame and engine numbers match those on the registration papers.
Have a suitable work area set aside
 Once you get the motorcycle home, make sure you have a spot where it can be left, preferably under shelter, so you can work on its easy. Take your time and work on it at least a couple of times a week. At first you're as keen as mustard, but after six months and a few setbacks you may be less keen. I like to work on my bikes straight after work for at least half an hour a few times a week. You have also got to consider your neighbours, as they will not like you cutting down your frame at 9pm in the evening! And be patient! Wait for the anti-seize to soak in before a second attempt at removing that stubborn bolt or nut. Just sit for ten minutes admiring your work or visualising what it could be, while the anti-seize does its work.

How I do mock-ups in Photoshop
                Speaking of visualizing, I do all of my mock ups on Photoshop. The important thing is to make sure that all the different parts are to scale. I do an Google image search and find a side view of the motorcycle I will be customising. The larger the image the better, an image that is only 640x480 is not really big enough to show much detail, 1640x1480 is what I would use as a minimum. How do you check everything is to scale? I use the motorcycle's wheel base as the starting point, because you can see it easily. Just measure between the front and rear axle nuts. Do a search for your motorcycle specifications and it will appear, typically it will be around 1500mm. Photoshop has rulers so you can scale it up or down to suit. See the image below for my example. I am using pixels as a unit of measure in the below example and then dividing it by ten. You can see this by the guides I have placed (2 x cyan coloured vertical lines) at about 1400mm.


Tuesday, September 2, 2014

How to make a rear wheel a front wheel - part 2




After grinding down the brake plate at the axle, the wheel is now centred in between the fork legs! The spacer on the opposite side now fits and is the correct width. The cover over the cush drive area needs a tidy up to make it look nice and the threaded bushes holding it on need to be made shorter to create more clearance on the fork leg........